Resetting ethernet connection Thema ist als GELÖST markiert

For service and support with i-Telex, its components and teleprinters in general

Moderator: M1ECY

Benutzeravatar

FredSonnenrein
Developer
Developer
Beiträge: 989
Registriert: Fr 3. Jun 2016, 13:49
Wohnort: Braunschweig
Hauptanschluß: 8579924 hawe d

Re: Resetting ethernet connection

#11

Beitrag von FredSonnenrein » So 10. Sep 2017, 18:22

Hi Paul

Today i intended to write you the procedure to enable the dhcp with the 'special procedure'.
But to be sure that i write every detail i tested the procedure at home and there i encountered that it doesn't work with the current software.
I will check why this is the case and will write again when i have the answer.

Best regards

Fred
Grüße,
Fred Sonnenrein, Braunschweig
i-Telex 8579924 (T100s) oder 781272 (T100) oder 792911 (T68d) oder 531075 (Creed75)


Topic author
arvadateletypes
Rank 2
Rank 2
Beiträge: 10
Registriert: Di 16. Mai 2017, 02:34
Hauptanschluß:

Re: Resetting ethernet connection

#12

Beitrag von arvadateletypes » So 10. Sep 2017, 19:33

Hi Fred,

Thank you for letting me know. I can be a "beta" tester of your procedure when you are ready with it.

Do you think I have a software (firmware) problem, or do I have a hardware problem (a bad board). I've visually checked all the solder joints and did not see anything. I'll look closer and also do some checking with a digital meter.

Paul

Benutzeravatar

FredSonnenrein
Developer
Developer
Beiträge: 989
Registriert: Fr 3. Jun 2016, 13:49
Wohnort: Braunschweig
Hauptanschluß: 8579924 hawe d

Re: Resetting ethernet connection

#13

Beitrag von FredSonnenrein » So 10. Sep 2017, 20:00

I'll let you know whan the working update is ready.
But the 'stuck' position shown in the log looks quite bad. If i have to guess then i would guess there is a hardware problem
Grüße,
Fred Sonnenrein, Braunschweig
i-Telex 8579924 (T100s) oder 781272 (T100) oder 792911 (T68d) oder 531075 (Creed75)

Benutzeravatar

FredSonnenrein
Developer
Developer
Beiträge: 989
Registriert: Fr 3. Jun 2016, 13:49
Wohnort: Braunschweig
Hauptanschluß: 8579924 hawe d

Re: Resetting ethernet connection

#14

Beitrag von FredSonnenrein » Mo 11. Sep 2017, 21:20

At first please install a new firmware (763) from here:

http://www.telexupdate.de/ethernet/update.zip

Then do the following steps to reset the DHCP option:

1. Restart the Ethernet board by switching power off and on again.
2. Within the next two seconds, before the red and yellow LED go off, press and hold the button at the Ethernet board
3. When the yellow LED is on (while the red one if off) release the button.
4. The yellow LED should go off and the red on again.
5. Press the button again for approx one second. While pressing the button the green led is on (with the red)
6. after releasing the button the led shall change from red+green to yellow+blue. This is the sign for the DHCP reset to take effect.
7. After that the Ethernet board starts again

Again if it still doesn't work send me the log debug again...

Fred
Grüße,
Fred Sonnenrein, Braunschweig
i-Telex 8579924 (T100s) oder 781272 (T100) oder 792911 (T68d) oder 531075 (Creed75)


Topic author
arvadateletypes
Rank 2
Rank 2
Beiträge: 10
Registriert: Di 16. Mai 2017, 02:34
Hauptanschluß:

Re: Resetting ethernet connection

#15

Beitrag von arvadateletypes » Di 12. Sep 2017, 04:14

Hi Fred,

The reset instructions worked as written. Now I know that the button works because this is the first time I've seen it do anything. I installed the firmware update, then followed steps 1-7. The lights worked exactly as documented.

Unfortunately the system still does not work. The log is as before, it stops after the SSD/MD error message and does not continue to the next step.

I've ordered a new ENC28J60 chip. We'll see if that fixes the problem.

Paul

Benutzeravatar

FredSonnenrein
Developer
Developer
Beiträge: 989
Registriert: Fr 3. Jun 2016, 13:49
Wohnort: Braunschweig
Hauptanschluß: 8579924 hawe d

Re: Resetting ethernet connection

#16

Beitrag von FredSonnenrein » Di 12. Sep 2017, 08:01

I will compare the "stuck position" with my station.The position where the program stucks is strange. There may be the problem of an unintended shortcut. It might be helpful to check this if you have the knowledge and tools.
Grüße,
Fred Sonnenrein, Braunschweig
i-Telex 8579924 (T100s) oder 781272 (T100) oder 792911 (T68d) oder 531075 (Creed75)

Benutzeravatar

FredSonnenrein
Developer
Developer
Beiträge: 989
Registriert: Fr 3. Jun 2016, 13:49
Wohnort: Braunschweig
Hauptanschluß: 8579924 hawe d

Re: Resetting ethernet connection

#17

Beitrag von FredSonnenrein » Mi 13. Sep 2017, 17:17

It's still strange. Please describt the status of the LEDs when the system stucks. It's still the save as in your video?
Grüße,
Fred Sonnenrein, Braunschweig
i-Telex 8579924 (T100s) oder 781272 (T100) oder 792911 (T68d) oder 531075 (Creed75)


Topic author
arvadateletypes
Rank 2
Rank 2
Beiträge: 10
Registriert: Di 16. Mai 2017, 02:34
Hauptanschluß:

Re: Resetting ethernet connection

#18

Beitrag von arvadateletypes » Mi 15. Nov 2017, 14:34

A final posting here to close this issue. Henning sent me a new board and all is working well now. I’m on-line!

Thanks for the help.

Antworten

Zurück zu „Service and Support“