czech version of t100 set up

For service and support with i-Telex, its components and teleprinters in general

Moderator: M1ECY

Benutzeravatar

WolfgangH
Rank 12
Rank 12
Beiträge: 550
Registriert: So 3. Jan 2021, 21:42
Wohnort: Kirchham (A)
Hauptanschluß: 978310 whoe a

Re: czech version of t100 set up

#31

Beitrag von WolfgangH »

That is good news and I learned again something new.

So, you can run the setup of your second port with your T1000S. ^^

I will show you the simple configuration:

Code: Alles auswählen

1 konfiguration tw39plus version 434 datum sep 24 2020
2 einfache konfiguration?	    j ok.
3 durchwahl aktuell: 11 neu:     .
4 pruefe 11 ok.
5 weiterleitungen abweisen? aktuell: nein neu:     . ok.
6 waehlscheibe vorhanden? aktuell: ja neu:     . ok.
7 laenge wahlauff-imp.? akt. 20/100 sek, neu:     . ok.
8 +++
The translation into English (I hope it helps):
1 ... -> gives you the information about your firmware version, might be different in your case
2 ... simple configuration? -> here you should answer just a "j", means ja (yes), if you answer "n" you will enter the extended configuration, which is not necessary for the first step)
3 ... current extension: 11 new: -> here you should enter a 2-digit number for the internal extension of your teleprinter, which is not used by any other device in your i-telex, answering with a "." keeps the current setting)
4 ... checking 11 ok. -> in case you entered a valid number, in the other case you have to repeat step 3!
5 ... deny forwarding? current: no new: -> possible answers are (j/n/.)
6 ... rotary dial available? current: yes new: -> possible answers are (j/n/.)
7 ... length of the dialling impulse? current 20/100 sec, new: -> enter a "." or a new value, hint: change only, if you encounter dialling troubles!
8 ... +++ -> means end of configuration
Folgende Benutzer bedankten sich beim Autor WolfgangH für den Beitrag (Insgesamt 2):
FranzReinholdKoch
Gruß
Wolfgang


Linz:
- 978310 whoe a - T100a
- 69558 kfrey d - T100s
- 978333 =whoe a - Minitelex
Kirchham: (Nachrichtenabruf an Wochenenden, Feiertagen, ...)
- 56449 sche d - T37i
- 11913 hoellw a - LO 3000 (100 Baud)
Benutzeravatar

FredSonnenrein
Developer
Developer
Beiträge: 2032
Registriert: Fr 3. Jun 2016, 13:49
Wohnort: Braunschweig
Hauptanschluß: 8579924 hawe d

Re: czech version of t100 set up

#32

Beitrag von FredSonnenrein »

Hi all,
levend hat geschrieben: So 18. Sep 2022, 12:41 What is even more interesting ----
On TW39 interface #1: the configuration menu is displayed normally on the teleprinter(the working one, T1000S), but in german. I left everything unchanged
There is the possibility to update the firmware of the TW39 card to an english version with the procedure explained here:

https://wiki.telexforum.de/index.php?ti ... faceBoards

The english version has the identificator
itlx_TW39plus-EN
available on beta_binaries.

For other boards ask for the available versions or see the page https://wiki.telexforum.de/index.php?ti ... -Varianten .
levend hat geschrieben: So 18. Sep 2022, 12:41 After I connect the T1000s teleprinter to TW39 interface #2, and long press the button on it: the teleprinter starts, the blue led is blinking on the interface card, but nothing was print out on the teleprinter.
Strange: Did only the blue LED blink? If so, the keypress was not detected as a long press, but as two short presses. But then, the T1000 should not have started. Does the red LED of the board goes on shortly on startup (as all but the ethernet board should do)?

Fred
Folgende Benutzer bedankten sich beim Autor FredSonnenrein für den Beitrag:
WolfgangH
Grüße,
Fred Sonnenrein, Braunschweig
i-Telex 952741 (Lo133), 531075 (Creed75), 8579924 (T100s), 781272 (T100), 792911 (T68d) oder 531072 (T.typ.72)
Bei besetzt oder gestört bitte 531002 versuchen.

levend
Rank 5
Rank 5
Beiträge: 41
Registriert: Mo 10. Mai 2021, 23:25
Wohnort: Budapest, HU
Hauptanschluß: 1604188

Re: czech version of t100 set up

#33

Beitrag von levend »

Hi Fred!

The FW was functioning perfectly, but I misplaced the TX optocoupler for interface 2, so data never actually left the card. After placing it correctly into it's socket, it worked without any further trouble.
Yes, red led was on too!
Best regards,
Balazs
Budapest, HU
Siemens T1000S - 1604188 elek h
iTelex: 1604188

levend
Rank 5
Rank 5
Beiträge: 41
Registriert: Mo 10. Mai 2021, 23:25
Wohnort: Budapest, HU
Hauptanschluß: 1604188

Re: czech version of t100 set up

#34

Beitrag von levend »

Some follow up questions:
- Is this machine supporting dual-ink ribbons? Black for local - red for remote messages?
- There is a key I cannot press no matter it's letter or figures mode engaged. What is the purpose of it? Pls see the attached image:
54B53A21-31A3-42E8-8764-1C65597D5449_1_201_a.jpeg
Du hast keine ausreichende Berechtigung, um die Dateianhänge dieses Beitrags anzusehen.
Best regards,
Balazs
Budapest, HU
Siemens T1000S - 1604188 elek h
iTelex: 1604188
Benutzeravatar

WolfgangH
Rank 12
Rank 12
Beiträge: 550
Registriert: So 3. Jan 2021, 21:42
Wohnort: Kirchham (A)
Hauptanschluß: 978310 whoe a

Re: czech version of t100 set up

#35

Beitrag von WolfgangH »

levend hat geschrieben: Di 20. Sep 2022, 18:20 - Is this machine supporting dual-ink ribbons? Black for local - red for remote messages?
The German T100S does, the Austrian export version also. I saw some Videos on YT of Zbrojovka Brno T100 with red and black text. So I assume your machine will provide this function as well.
levend hat geschrieben: Di 20. Sep 2022, 18:20 - There is a key I cannot press no matter it's letter or figures mode engaged. What is the purpose of it? Pls see the attached
This key represents the code 32. On a punch tape no holes are punched. On some teleprinters you can activate the 3rd level. (special characters) Usually this key is blocked by a wire clip. (can be removed)
Folgende Benutzer bedankten sich beim Autor WolfgangH für den Beitrag (Insgesamt 2):
levendFranz
Gruß
Wolfgang


Linz:
- 978310 whoe a - T100a
- 69558 kfrey d - T100s
- 978333 =whoe a - Minitelex
Kirchham: (Nachrichtenabruf an Wochenenden, Feiertagen, ...)
- 56449 sche d - T37i
- 11913 hoellw a - LO 3000 (100 Baud)

levend
Rank 5
Rank 5
Beiträge: 41
Registriert: Mo 10. Mai 2021, 23:25
Wohnort: Budapest, HU
Hauptanschluß: 1604188

Re: czech version of t100 set up

#36

Beitrag von levend »

WolfgangH hat geschrieben: Di 20. Sep 2022, 18:46
levend hat geschrieben: Di 20. Sep 2022, 18:20 - Is this machine supporting dual-ink ribbons? Black for local - red for remote messages?
The German T100S does, the Austrian export version also. I saw some Videos on YT of Zbrojovka Brno T100 with red and black text. So I assume your machine will provide this function as well.
Should I change something? Because right now it does not raise the ribbon differently for remote/local messages
Best regards,
Balazs
Budapest, HU
Siemens T1000S - 1604188 elek h
iTelex: 1604188
Benutzeravatar

WolfgangH
Rank 12
Rank 12
Beiträge: 550
Registriert: So 3. Jan 2021, 21:42
Wohnort: Kirchham (A)
Hauptanschluß: 978310 whoe a

Re: czech version of t100 set up

#37

Beitrag von WolfgangH »

Have you inserted a two coloured ribbon?

I'm asking, because in your video I see only a black coloured one in your machine.

Gruß
Wolfgang


Linz:
- 978310 whoe a - T100a
- 69558 kfrey d - T100s
- 978333 =whoe a - Minitelex
Kirchham: (Nachrichtenabruf an Wochenenden, Feiertagen, ...)
- 56449 sche d - T37i
- 11913 hoellw a - LO 3000 (100 Baud)

levend
Rank 5
Rank 5
Beiträge: 41
Registriert: Mo 10. Mai 2021, 23:25
Wohnort: Budapest, HU
Hauptanschluß: 1604188

Re: czech version of t100 set up

#38

Beitrag von levend »

Yes, I did, but just today - it only arrived in the afternoon - so that's why it's not in the video.
I'm still lucky that there are suppliers in Hungary where I can purchase these locally. Not so lucky with paper rolls - I usually use thermofax paper, that's still available.
Best regards,
Balazs
Budapest, HU
Siemens T1000S - 1604188 elek h
iTelex: 1604188
Benutzeravatar

DF3OE
Founder
Founder
Beiträge: 2464
Registriert: Di 7. Jun 2016, 09:45
Wohnort: Edemissen- Blumenhagen
Hauptanschluß: 925302 treu d
Kontaktdaten:

Re: czech version of t100 set up

#39

Beitrag von DF3OE »

Don't use Telefax paper, it has chemicals on the surface that can harm the print head.
You can still purchase original Telex paper here on the forum from Werner in Aschaffenburg or from other sources in Germany.
Punch tape is also available from Werner or me.

Two colours printing for the T100 was an option
Not all are fitted with it.
Folgende Benutzer bedankten sich beim Autor DF3OE für den Beitrag (Insgesamt 2):
Franzlevend
mfg
henning +++

925302 treu d - T1000Z (Hauptanschluss)
55571 fvler a - T100S
210911za hmb d - T150 (Werkstatt)
218308 test d - T1000S/LS (Werkstatt)
925333 =treu d (Minitelex Sanyo SF100)
Fax G2/G3: 05176-9754481 (Sanyo SF100 Thermofax)
Antworten

Zurück zu „Service and Support“